DodgeRam.info > TSB's > 23-015-05

TSB 23-015-05

Superseded by TSB 23-020-06. Left for reference only.

Visit Geno's Garage
for Truck accessories.
Geno's Garage Truck Accessories

Date: March 9, 2005     Transit Film Removal

THIS BULLETIN SUPERSEDES TECHNICAL SERVICE BULLETIN 23-043-04, DATED OCTOBER 20,2004, WHICH SHOULD BE REMOVED FROM YOUR FILES.

Models: 2004 - 2006 (DR) Ram Truck

2002 - 2006 (PT) Chrysler PT Cruiser/Chrysler PT Cruiser Convertible
2004 - 2006 (DR) Ram Truck

Discussion:
Transit Film Removal Process
1.    Wet vehicle thoroughly using cool to warm water.
NOTE. NEVER USE HOT WATER TO REMOVE FILM: THE FILM IS DESIGNED TO REMOVE EASILY FROM THE SURFACE AT AMBIENT TEMPERATURES BETWEEN 16° C. and 32° C. (60° F. AND 90° F.).
2. Peel the film off using cold to warm water from a garden hose or pressure washer system. Combine the peeling of the film with one hand while directing the water pressure with the other.
NOTE: PRESSURE WASHER MAY HAVE A PRESSURE UP TO 13790 kPa (2000 psi.).
CAUTION: USE GLOVES THAT WILL PROTECT YOUR HANDS FROM WATER PRESSURES CREATED BY THE PRESSURE WASHER SYSTEM.
3. Transit film may leave a wax haze on surface. Wash vehicle with soap and water to remove.
   
NOTE: Painted surfaces of the vehicle that are covered for extended periods of time with transit film may appear to have a white "milky" spot(s) on dark colors, or a fogging, coffee colored spot lighter colors (front end covers or magnetic signs can cause the same condition) and can be corrected with the following steps:
1. Place a heat gun approximately 100 to 150 mm (4 to 6 inches) from the effected area. A target surface temperature of 80° to 95° C. (180° to 200°F.) is preferred. DO NOT APPLY HEAT ABOVE 95° C. (200°F.) TO ANY PLASTIC PARTS.
2. Heat the effected area for approximately 2 to 4 minutes. The amount of time is dependent upon the size and shape of the affected area and the severity of the condition. CIRCULATE THE HEAT GUN AROUND THE EFFECTED AREA. DO NOT ALLOW HEAT TO BE DIRECTED AT ONE AREA FOR TOO LONG, PAINT DAMAGE MAY OCCUR
3. If this Repair Procedure does not correct the condition, color-coat paint repair will be required.
Additional Precautions To Take When Removing Transit Film From Vehicles Equipped With Flame Package Decals.
1. Take care not to lift edges of decals when removing film.
2. Peel film away from decals starting from the large decal surface areas toward the smaller decal surface areas. Pull on the film so the film already peeled away is above the still adhered film and at 45° angle to the surface.
Additional Steps When Transit Film Has Been On The Vehicle For 6 Months Or Longer; When Film Is Extremely Dirty In Appearance; When Film Is Stubborn To Peel Off By Hand.
1. Wet vehicle thoroughly using cool to warm water.
NOTE: NEVER USE HOT WATER TO REMOVE FILM: THE FILM IS DESIGNED TO REMOVE EASILY FROM THE SURFACE AT AMBIENT TEMPERATURES BETWEEN 16° C. and 32° C. (60° F. AND 90° F.).
2. Soak film using cold to warm water and wash thoroughly using Mopar Car Wash Soap Concentrate (p/n 05017212AB) or equivalent and water. If film is extremely dirty, use a 1. woolen" car wash mitt, wet surface and pour Mopar Car Wash Soap Concentrate directly onto surface and thoroughly wash the film.
3. Repeat the water soaking process, until the film turns from clear to a milky white appearance. When the film turns milky white, release agents in the film have been activated allowing the film to be removed from the surface using a pressure washer. In extreme conditions, soak towels in warm soapy water and place directly on the film surface where the film is difficult to remove, keeping the surface wet for 10-15 minutes. When film turns milky white, remove towels and use pressure washer to remove the film.
Removal of small film particles on paint surface:
1. Use Mopar Windshield Washer Solvent (p/n 04318067AB) or equivalent (methyl alcohol, methanol based). Pour directly onto a clean soft dry cloth (do not dilute the solvent). The concentrated solvent will instantly dissolve the transit film particles from paint surfaces or acrylic lenses, acrylic emblems, polycarbonate, lexan surfaces, or unsealed rubber surfaces.
NOTE: ALWAYS WEAR RUBBER GLOVES AND FOLLOW MANUFACTURER'S INSTRUCTIONS WHEN HANDLING CHEMICAL SUBSTANCES.
NOTE: NEVER POUR SOLVENTS ONTO THE FILM FOR REMOVAL. THE FILM WILL ALWAYS COME OFF WITH SOAP AND WATER PRESSURE.
NOTE: PLACE A WIRE SCREEN OVER BRAIN TO THE STOP FILM FROM ENTERING AND CLOGGING SEWER DRAIN. TRANSIT FILM IS A CLASS It INDUSTRIAL NON-HAZARDOUS WASTE AND SHOULD BE DISPOSED OF ACCORDINGLY.

Parts Required:
Qty. Part No. Description
AR 05017212AB Car Wash Concentrate, 8 oz.
AR 05013678ABAB Car Wash Concentrate, 5 gal.
AR 04318067AB Windshield Washer Cleaner

NOTE: If you have any problems removing the film using this SB you can contact the supplier field engineers. They will either visit your dealership or walk you through the process. The contacts are Robert (Bob) Guenther or Robert Boyd, they can be contacted at 1-800-307-7218.

Policy:   Information Only


I would like to thank Bob Bergevin, Arthur Cantrall, Barry Drodge, David Lovell, Bill Maurits, and Steve for supplying the information for these bulletins. And a big thank you goes to Geno's Garage for making DodgeRam.info possible.

 

  Top of Page  

  DodgeRam.info Home  

 

This page was edited on: May 3, 2004